Comfort Zone or DR-910F, two hardwired heaters

Neither has a plug. Both go up on a ceiling or wall, wired straight to a 240 V circuit by an electrician. The Comfort Zone CZ220 gives up to 5,000 W from the $ band, and the Dr. Infrared DR-910F gives 10,000 W from the $$$ band.

The CZ220 for a sealed two-car garage, the DR-910F for a big shop

For an insulated two-car garage, the Comfort Zone CZ220 gives enough heat for the least money. It hangs from the ceiling, frees the floor and runs on the same 30 A circuit a plug-in 5,600 W heater would need.

The Dr. Infrared DR-910F is the heavy hitter, at twice the output. It suits a three-car garage, a pole barn shop or a space with a tall ceiling, and it asks for a much bigger circuit to match.

Both sit in our electric garage heaters compared, the CZ220 as the budget ceiling pick and the DR-910F as pick 4 for big garages. The DR-910F also meets the 7,500 W InoKraft, and the CZ220 faces our top-pick Dr. Infrared.

Comfort Zone CZ220 and DR-910F side by side

Figures come from the Amazon.com listings. Comfort Zone claims 1,000 sq ft for 5,000 W, which is generous, so the table puts our rule-of-thumb figure beside it.

FeatureComfort Zone CZ220Dr. Infrared DR-910F
TypeFan-forced ceiling heater, hardwiredFan-forced wall or ceiling heater, hardwired
Heat output3,000, 4,000 or 5,000 W; 17,065 BTU on high10,000 W (about 34,100 BTU per hour)
Current draw20.9 A42 A in the spec table
Supply needed240 V circuit, typically 30 A with 10 AWG copperDedicated 240 V line, 60 A breaker typical, 6 AWG copper as the listing names
InstallElectrician; no cord or plug in the boxElectrician; no cord or plug in the box
MountingCeiling bracket, adjustable angle, louversWall or ceiling bracket, five adjustable louvers
Thermostat and controlsThermostat knob and heat-setting knob, up to 95 °F, power lightThermostat on a remote, 50 to 85 °F, with a timer and one fan speed
Rated area1,000 sq ft (maker); nearer 500 sq ft by our rule of thumbNo maker figure; roughly 1,000 sq ft of insulated floor by our rule
Size and weight14.02 × 12.91 × 10.63 in, 20.4 lb49 lb; 22 × 18 × 16 in
Price band$$$$
Warranty1 year, manufacturer defects1 year limited, parts and labor

How far 5,000 W and 10,000 W reach

On the rule of 10 W for every square foot of insulated floor, the CZ220 covers roughly 500 sq ft on high and the DR-910F roughly 1,000 sq ft. That makes the maker’s 1,000 sq ft claim for the CZ220 optimistic by about half.

The CZ220 can also drop to 3,000 or 4,000 W, which is handy for holding a frost-safe 40 to 50 °F on a mild night. For the DR-910F no lower heat setting is listed, leaving the thermostat to switch all 10,000 W on and off.

Our sizing guide works out which class your floor and ceiling call for. Many two-car garages land nearer the CZ220.

Round goes to the DR-910F for big spaces, to the CZ220 for a two-car garage.

A 30 A circuit for one, 60 A for the other

Both need a licensed electrician, a dedicated double-pole breaker and a permit where your town requires one. The difference is size. At 20.9 A the CZ220 typically sits on a 30 A breaker with 10 AWG copper, a circuit most panels can find room for.

At about 42 A, the DR-910F typically needs a 60 A breaker and the 6 AWG copper its listing names. Some older or smaller panels cannot spare that, so ask the electrician to check capacity before you order.

Diagram of a 240 V garage heater circuit: a double-pole breaker in the main panel, a copper cable to an outlet or a hardwired box, and a heater mounted high on the garage wall, with a table of typical breaker and wire sizes
A 240 V heater gets its own circuit: a double-pole breaker, copper wire sized for it, and an outlet or a hardwired connection. The sizes shown are typical for a continuous load; your electrician and the heater’s manual decide.

Our 240 V wiring guide covers what the job involves. Never upsize a breaker on existing wire, because the breaker is there to protect the wire.

Round goes to the CZ220, for the lighter circuit.

Hanging the CZ220 and the DR-910F

The CZ220 weighs 20.4 lb and hangs from a ceiling bracket with an adjustable angle and louvers. The DR-910F weighs 49 lb and can go on a wall or ceiling, so it needs solid framing behind the bracket.

Mount either one high, aim it at the bench or the car bay at an angle, and keep the manual’s clearances. The guide to mounting a garage heater goes through angles and the clear space below.

Round goes to the CZ220, at well under half the weight.

Knobs on the ceiling or a remote in your hand

The CZ220 uses two knobs on the heater, one for the thermostat and one for the heat setting, which means a ladder each time you change them. Owners give its temperature regulation mixed reports.

The DR-910F has a remote-controlled thermostat from 50 to 85 °F and a timer, so you set it from the floor. Owners of the Dr. Infrared shop heaters say it is not always accurate. Our thermostat guide explains why a heater’s own sensor reads off.

Round goes to the DR-910F, for the remote.

Steel bodies, fan noise in the owner reports

Comfort Zone uses a heavy-gauge steel body and an overheat sensor with automatic shut-off. Owners say it heats well and installs easily, while noise gets mixed reports and some units failed early, a few within weeks.

The DR-910F has a heavy-duty, fully enclosed motor and UL and cUL listings. Owners report plenty of fast heat but also a noisy fan that can rattle, on a review pool shared with other Dr. Infrared models.

Round is a draw, solid builds with noise complaints on both.

The $ band against the $$$ band

The CZ220 is in the $ band, under $100, and shares that band only with the 120 V NewAir in our lineup. The DR-910F is in the $$$ band, over $250, and its 60 A circuit adds more on top.

Both carry a 1-year warranty, with Dr. Infrared spelling out parts and labor. Per watt, the CZ220 is the bargain, as long as 5,000 W suits your garage.

Round goes to the CZ220, by a wide margin.

The CZ220 comes with a generous area claim and knobs you reach by ladder, and some owners report early failures. The DR-910F needs a 60 A circuit not every panel can spare and framing for 49 lb, and owners call its fan loud.

A ceiling heater for your garage, or for a shop

For a sealed two-car garage, the CZ220 is a lot of heat for the money and keeps the floor clear. If the space is big, tall or hard to insulate, the DR-910F is the one that keeps up, once your electrician confirms the panel can feed it.

Questions and answers

More questions about the Comfort Zone CZ220 and the Dr. Infrared DR-910F

Can I add a plug to the Comfort Zone CZ220?

No. It ships without a cord or plug and is made to be hardwired. Converting it is not something to improvise. Have a licensed electrician wire it to a dedicated 240 V circuit as the manual describes.

Does the CZ220 really heat 1,000 sq ft?

That is the maker’s claim. The common 10 W per square foot rule for an insulated garage puts 5,000 W nearer 500 sq ft, and an uninsulated space less than that.

What breaker does the DR-910F need?

A 42 A heater usually gets a 60 A two-pole breaker and the 6 AWG copper its listing names, because heating is a continuous load. Your electrician and local code decide the final sizes.

Which one is easier to adjust?

The DR-910F, because its thermostat and timer work from a remote. The CZ220 has two knobs on the heater itself, so with a ceiling mount you need a ladder or a step stool to change them.

Can either heater use a wall thermostat?

Hardwired heaters can often work with a separate wall thermostat placed away from the heater, which regulates better. Check the manual for your model and let the electrician wire it.